( pcb2gcode 2.5.0 )
( Software-independent Gcode )

G94 ( Millimeters per minute feed rate. )
G21 ( Units == Millimeters. )

G90 ( Absolute coordinates. )
G00 S24000 ( RPM spindle speed. )
G01 F400.00000 ( Feedrate. )


G00 Z35.00000 (Retract to tool change height)
T1
M5      (Spindle stop.)
G04 P1.00000 (Wait for spindle to stop)
(MSG, Change tool bit to cutter diameter 2.10000mm)
M0      (Temporary machine stop.)
M3 ( Spindle on clockwise. )
G04 P1.00000 (Wait for spindle to get up to speed)
G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G00 Z2.00000 ( retract )

G00 X101.04999 Y-49.99998 ( rapid move to begin. )
G01 Z-4.00000 F50.00000 ( plunge. )
G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G01 F400.00000
G01 X101.04996 Y-26.29491
G00 Z0.00000
G01 X101.04996 Y-23.69491
G01 Z-4.00000 F50.00000
G01 F400.00000
G01 X101.04993 Y0.01016
G01 X101.03891 Y0.15217
G01 X101.00876 Y0.29136
G01 X100.98666 Y0.35911
G01 X100.95588 Y0.43449
G01 X100.88826 Y0.55984
G01 X100.80434 Y0.67490
G01 X100.70559 Y0.77757
G01 X100.64323 Y0.82989
G01 X100.58544 Y0.87163
G01 X100.46210 Y0.94282
G01 X100.35911 Y0.98666
G01 X100.24214 Y1.02169
G01 X100.12189 Y1.04290
G01 X100.00000 Y1.04999
G01 X51.30001 Y1.04999
G00 Z0.00000
G01 X48.70001 Y1.04999
G01 Z-4.00000 F50.00000
G01 F400.00000
G01 X0.00002 Y1.04999
G01 X-0.08133 Y1.04684
G01 X-0.15215 Y1.03891
G01 X-0.29134 Y1.00876
G01 X-0.35908 Y0.98666
G01 X-0.43447 Y0.95588
G01 X-0.55982 Y0.88826
G01 X-0.67488 Y0.80434
G01 X-0.77755 Y0.70559
G01 X-0.82987 Y0.64323
G01 X-0.87160 Y0.58544
G01 X-0.94280 Y0.46210
G01 X-0.98664 Y0.35911
G01 X-1.02167 Y0.24214
G01 X-1.04288 Y0.12189
G01 X-1.04996 Y0.00000
G01 X-1.04994 Y-23.70507
G00 Z0.00000
G01 X-1.04994 Y-26.30507
G01 Z-4.00000 F50.00000
G01 F400.00000
G01 X-1.04991 Y-50.01014
G01 X-1.03889 Y-50.15215
G01 X-1.00874 Y-50.29134
G01 X-0.98664 Y-50.35908
G01 X-0.95586 Y-50.43447
G01 X-0.88824 Y-50.55982
G01 X-0.80432 Y-50.67488
G01 X-0.70556 Y-50.77755
G01 X-0.64321 Y-50.82987
G01 X-0.58542 Y-50.87160
G01 X-0.46208 Y-50.94277
G01 X-0.35908 Y-50.98664
G01 X-0.24212 Y-51.02167
G01 X-0.12187 Y-51.04285
G01 X0.00002 Y-51.04996
G01 X48.70509 Y-51.04994
G00 Z0.00000
G01 X51.30509 Y-51.04994
G01 Z-4.00000 F50.00000
G01 F400.00000
G01 X100.01016 Y-51.04991
G01 X100.11176 Y-51.04397
G01 X100.21232 Y-51.02824
G01 X100.31087 Y-51.00290
G01 X100.40650 Y-50.96805
G01 X100.49832 Y-50.92418
G01 X100.58544 Y-50.87160
G01 X100.66708 Y-50.81082
G01 X100.74244 Y-50.74242
G01 X100.81084 Y-50.66706
G01 X100.87163 Y-50.58542
G01 X100.92420 Y-50.49830
G01 X100.97201 Y-50.39708
G01 X101.00587 Y-50.30112
G01 X101.03030 Y-50.20231
G01 X101.04506 Y-50.10163
G01 X101.04999 Y-49.99998

G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G00 Z35.000000 ( retract )

M5 ( Spindle off. )
G04 P1.000000
M9 ( Coolant off. )
M2 ( Program end. )