# SSD1306 OLED Servo Control with STM32 Blue Pill

This project demonstrates how to control a servo motor using an IBT_2 (BTS7960) motor driver, an STM32 Blue Pill, and a 128x64 SSD1306 OLED display. The user can control the motor's speed and direction using four push buttons, with real-time feedback on the OLED screen. It shows how to use the DAPLink programmer in Arduino IDE v2 with debugging.

## Features

*   **Motor Control:** Adjust speed and direction of a servo motor.
*   **OLED Display:** A 128x64 SSD1306 OLED display shows the current speed, direction, and motor state (ON/OFF).
*   **User Interface:** A simple and intuitive interface with four buttons for control (Up, Down, OK, Cancel).
*   **Two-Color Display Optimization:** The UI is designed for two-color (Yellow and Blue) OLED displays, with a static header in the yellow section and dynamic values in the blue section.

## Hardware Required

*   STM32F103C8T6 "Blue Pill" development board
*   128x64 SSD1306 OLED display (I2C) with 4 push buttons (up, down, OK, Back)
*   IBT_2 (dual BTS7960) motor driver
*   Servo motor e.g.: RS-550 or R-775
*   External power supply for the motor 12-24V/5A
*   Breadboard and jumper wires

## Wiring

Connect the components to the Blue Pill as described below.

### OLED Display (I2C)

| OLED Display Pin | Blue Pill Pin |
| :--------------- | :------------ |
| VCC              | 3.3V          |
| GND              | GND           |
| SCL              | PB6           |
| SDA              | PB7           |

### Control Buttons

The buttons are connected to GPIO pins using the internal pull-up resistors. The other terminal of each button should be connected to GND.

| Button Function | Blue Pill Pin |
| :-------------- | :------------ |
| Up              | PA0           |
| Down            | PA1           |
| OK              | PA2           |
| Cancel          | PA3           |

### IBT_2 Motor Driver

The IBT_2 module requires its own power supply for the motor.

| IBT_2 Pin | Blue Pill Pin | Description                    |
| :-------- | :------------ | :---------------------------   |
| VCC       | 5V            | Logic Power                    |
| GND       | GND           | Logic Ground                   |
| R_EN      | 3.3V          | Right Enable (connect to 3.3V) |
| L_EN      | 3.3V          | Left Enable (connect to 3.3V)  |
| RPWM      | PB0           | Right PWM Signal (Forward)     |
| LPWM      | PB1           | Left PWM Signal (Reverse)      |

### DAPLink UART

For debugging and logging, you can connect the DAPLink's virtual COM port to the Blue Pill's UART1.

| DAPLink Pin | Blue Pill Pin | Description         |
| :---------- | :------------ | :------------------ |
| RXD         | PA9 (TX1)     | Connect to TX       |
| TXD         | PA10 (RX1)    | Connect to RX       |
| GND         | GND           | Common Ground       |

**IBT_2 Power Connections:**

| IBT_2 Terminal | Connection                     |
| :------------- | :----------------------------- |
| B+             | Positive of Motor Power Supply |
| B-             | Negative of Motor Power Supply |
| M+             | Positive of Servo Motor        |
| M-             | Negative of Servo Motor        |

## Dependencies

This sketch requires the following Arduino libraries:
*   `Wire`
*   `Adafruit_GFX`
*   `Adafruit_SSD1306`
*   `Adafruit_BusIO` (A dependency for the Adafruit libraries)

## Getting Started

### Prerequisites

*   [Arduino CLI](https://arduino.github.io/arduino-cli/installation/)
*   [STMicroelectronics STM32 core](https://github.com/stm32duino/Arduino_Core_STM32)

### Installation

1.  **Install arduino-cli:** Follow the official instructions at [arduino.github.io/arduino-cli/installation/](https://arduino.github.io/arduino-cli/installation/).

2.  **Initialize and Configure arduino-cli:**
    *   Create a default configuration file:
        ```bash
        arduino-cli config init
        ```
    *   Add the STMicroelectronics board manager URL:
        ```bash
        arduino-cli config add board_manager.additional_urls https://github.com/stm32duino/BoardManagerFiles/raw/main/package_stmicroelectronics_index.json
        ```
    *   Update the local core index:
        ```bash
        arduino-cli core update-index
        ```
    *   Install the STM32 core:
        ```bash
        arduino-cli core install STMicroelectronics:stm32
        ```

3.  **Install Required Libraries:**
    ```bash
    arduino-cli lib install "Adafruit SSD1306" "Adafruit GFX Library" "Adafruit BusIO"
    ```

## Board Setup

In Arduino IDE → Tools, set:

    Board → STM32 MCU based boards → Generic STM32F1 series

    Board part number → BluePill F103CB (or C8 with 128K)

    Upload Method → OpenOCD DAPLink (SWD)

## Compilation

1.  **Prepare Your Sketch Directory:** Ensure your sketch file is named `SSD1306_sketch.ino` and is located in a folder with the same name. For example:
    `/path/to/your/project/SSD1306_sketch/SSD1306_sketch.ino`

2.  **Compile the Sketch:** Compile the sketch for the Blue Pill (STM32F103CB or C8 with 128k), specifying the OpenOCD upload method.
    ```bash
    arduino-cli compile --fqbn STMicroelectronics:stm32:GenF1:pnum=BLUEPILL_F103CB,upload_method=OpenOCDDapLink /path/to/your/project/SSD1306_sketch
    ```
    The binary files will be generated in a temporary build directory. To find the path to the binary, you can run the compile command with the `--verbose` flag.

## Upload to the Board

The compiled sketch can be uploaded to the Blue Pill using `openocd`. The exact command may vary depending on your setup.

First, you need to find the path to your compiled `.elf` file. You can find this in the output of the `arduino-cli compile` command. It will be in a temporary directory `~/.cache/arduino/sketches`.

Then, find the `openocd` e.g.: `~/.arduino15/packages/STMicroelectronics/tools/xpack-openocd/0.12.0-6/bin/openocd` or install a distro specific version e.g.: `sudo apt install openocd`. Example of the path to the compiled sketch: `/home/martin/.cache/arduino/sketches/96DBB1C909C240C2F96DCDD5DDFB9A12/SSD1306_sketch.ino.elf`

Here is an example command to upload the sketch using DAPLink:

```bash
/path/to/your/openocd -d2 -f interface/cmsis-dap.cfg -f target/stm32f1x.cfg -c "program {/path/to/your/sketch.ino.elf} verify reset exit"
```

## 🐞 Hardware Debugging with DAPLink (CMSIS-DAP) on Blue Pill

This section describes how to enable **hardware debugging** for the STM32F103 "Blue Pill" board using a **DAPLink / CMSIS-DAP** debugger in **Arduino IDE 2**.  
By default, the STM32 Arduino core loads the wrong OpenOCD configuration (`dapdirect_swd`, meant for ST-Link).

Until the [issues/2807](https://github.com/stm32duino/Arduino_Core_STM32/issues/2807) is not fixed, follow these steps to work around it:

### 🧭 1. Locate STM32 Core Folder (Linux)

Open a terminal and navigate to your STM32 Arduino core installation:

```bash
cd ~/.arduino15/packages/STMicroelectronics/hardware/stm32/2.11.0/
```
Adjust the version number if different (check in Arduino IDE → Tools → Board → Boards Manager).

🧰 2. Create or Edit `platform.local.txt`

Create (or edit) a local override file:

```bash
nano platform.local.txt
```

Paste the following lines:

```bash
debug.server.openocd.scripts.0=interface/cmsis-dap.cfg
debug.server.openocd.scripts.1={runtime.platform.path}/debugger/select_swd.cfg
```

Save and close (Ctrl + O, Enter, Ctrl + X).

These lines tell OpenOCD to:

- Use the CMSIS-DAP interface `interface/cmsis-dap.cfg`

- Use standard SWD transport `select_swd.cfg` instead of `dapdirect_swd`

🔁 3. Restart Arduino IDE

Completely close and reopen Arduino IDE 2 to apply the new settings.

⚙️ 4. Configure the IDE

In Arduino IDE → Tools, set:

- Debug symbols and core logs → Core Logs and Symbols Enabled (-g)

- Optimize → Debug (-Og)

Then click the 🐞 Debug icon and press Start Debugging.