166 lines
3.2 KiB
YAML
166 lines
3.2 KiB
YAML
board: PiBot V4.7B
|
|
name: 3040L CNC
|
|
meta: v1.0.0
|
|
stepping:
|
|
engine: I2S_STREAM
|
|
idle_ms: 254
|
|
pulse_us: 4
|
|
dir_delay_us: 1
|
|
disable_delay_us: 0
|
|
|
|
axes:
|
|
shared_stepper_disable_pin: NO_PIN
|
|
x:
|
|
steps_per_mm: 320.000
|
|
max_rate_mm_per_min: 3000.000
|
|
acceleration_mm_per_sec2: 150.000
|
|
max_travel_mm: 290.000
|
|
soft_limits: false
|
|
homing:
|
|
cycle: 2
|
|
positive_direction: false
|
|
mpos_mm: 0.000
|
|
feed_mm_per_min: 100.000
|
|
seek_mm_per_min: 1000.000
|
|
settle_ms: 500
|
|
seek_scaler: 1.100
|
|
feed_scaler: 1.100
|
|
|
|
motor0:
|
|
limit_neg_pin: gpio.26:low
|
|
limit_pos_pin: NO_PIN
|
|
limit_all_pin: NO_PIN
|
|
hard_limits: false
|
|
pulloff_mm: 1.000
|
|
standard_stepper:
|
|
step_pin: I2SO.2
|
|
direction_pin: I2SO.1
|
|
disable_pin: I2SO.0
|
|
|
|
y:
|
|
steps_per_mm: 320.000
|
|
max_rate_mm_per_min: 3000.000
|
|
acceleration_mm_per_sec2: 150.000
|
|
max_travel_mm: 390.000
|
|
soft_limits: false
|
|
homing:
|
|
cycle: 2
|
|
positive_direction: false
|
|
mpos_mm: 0.000
|
|
feed_mm_per_min: 100.000
|
|
seek_mm_per_min: 1000.000
|
|
settle_ms: 500
|
|
seek_scaler: 1.100
|
|
feed_scaler: 1.100
|
|
|
|
motor0:
|
|
limit_neg_pin: gpio.33:low
|
|
limit_pos_pin: NO_PIN
|
|
limit_all_pin: NO_PIN
|
|
hard_limits: false
|
|
pulloff_mm: 1.000
|
|
standard_stepper:
|
|
step_pin: I2SO.5
|
|
direction_pin: I2SO.4
|
|
disable_pin: I2SO.7
|
|
|
|
z:
|
|
steps_per_mm: 320.000
|
|
max_rate_mm_per_min: 1500.000
|
|
acceleration_mm_per_sec2: 100.000
|
|
max_travel_mm: 80.000
|
|
soft_limits: false
|
|
homing:
|
|
cycle: 1
|
|
positive_direction: true
|
|
mpos_mm: 0.000
|
|
feed_mm_per_min: 100.000
|
|
seek_mm_per_min: 800.000
|
|
settle_ms: 500
|
|
seek_scaler: 1.100
|
|
feed_scaler: 1.100
|
|
|
|
motor0:
|
|
limit_neg_pin: NO_PIN
|
|
limit_pos_pin: gpio.32:low
|
|
limit_all_pin: NO_PIN
|
|
hard_limits: false
|
|
pulloff_mm: 1.000
|
|
standard_stepper:
|
|
step_pin: I2SO.10
|
|
direction_pin: I2SO.9
|
|
disable_pin: I2SO.8
|
|
|
|
i2so:
|
|
bck_pin: gpio.22
|
|
data_pin: gpio.21
|
|
ws_pin: gpio.17
|
|
|
|
spi:
|
|
miso_pin: gpio.19
|
|
mosi_pin: gpio.23
|
|
sck_pin: gpio.18
|
|
|
|
sdcard:
|
|
card_detect_pin: NO_PIN
|
|
cs_pin: gpio.5
|
|
|
|
probe:
|
|
pin: gpio.2:low
|
|
toolsetter_pin: NO_PIN
|
|
|
|
start:
|
|
must_home: false
|
|
|
|
# Begin OLED
|
|
i2c0:
|
|
sda_pin: gpio.27
|
|
scl_pin: gpio.25
|
|
|
|
oled:
|
|
i2c_num: 0
|
|
i2c_address: 60
|
|
width: 128
|
|
height: 64
|
|
radio_delay_ms: 1000
|
|
|
|
# Using MOSFETs
|
|
coolant:
|
|
flood_pin: gpio.12
|
|
mist_pin: gpio.4
|
|
delay_ms: 0
|
|
|
|
################################################################################################################################
|
|
|
|
# Begin Huanyang RS485
|
|
uart1:
|
|
txd_pin: gpio.15
|
|
rxd_pin: gpio.16
|
|
rts_pin: gpio.14
|
|
baud: 9600
|
|
mode: 8N1
|
|
|
|
Huanyang:
|
|
uart_num: 1
|
|
modbus_id: 1
|
|
tool_num: 1
|
|
speed_map: 0=0% 0=25% 6000=25% 24000=100%
|
|
off_on_alarm: true
|
|
|
|
# Begin 10V
|
|
# 10V:
|
|
# forward_pin: gpio.15
|
|
# reverse_pin: gpio.14
|
|
# pwm_hz: 5000
|
|
# output_pin: gpio.13
|
|
# enable_pin: NO_PIN
|
|
# direction_pin: NO_PIN
|
|
# disable_with_s0: false
|
|
# s0_with_disable: true
|
|
# spinup_ms: 0
|
|
# spindown_ms: 0
|
|
# tool_num: 0
|
|
# speed_map: 0=0% 6000=25% 24000=100%
|
|
# off_on_alarm: false
|
|
|
|
# End of File |